Table of Contents
PC running slow?
You should review these troubleshooting guidelines if your computer has a fatal system error, error code 0x0000002e 0x00000000.
Our server HP DL 580 G5 (Win 2003 – x64) restarted today for obvious reasons.
1 POST error: Fatal error occurred before power on. 12/05/2008 11:44 12/05/2008 11:44 am required
2 POST errors: 05.12.2008 11:44 05.12.2008 11:44 1
ASR pair recognized by system ROM 12/05/2008 11:44 12/05/2008 11:44 AM 1
some An unrecoverable system error has occurred (error code 0x0000002E, 0x00000000) 05/12/2008 11:33 05/12/2008 11:33 AM 1
I connect either internally or externally. But I was confused by the display on physical disks.
I buy 6 internal drives and 1 external.
Physical Drive 1I: 1: 9 (Port 1I: Block 1: Required Bay, SATA 4 HDD, TB, OK)
PC running slow?
ASR Pro is the ultimate solution for your PC repair needs! Not only does it swiftly and safely diagnose and repair various Windows issues, but it also increases system performance, optimizes memory, improves security and fine tunes your PC for maximum reliability. So why wait? Get started today!
physical drive 1I: 1: 11 (port 1I: chassis 1: bay 11, 6TB SATA HDD, normal)
physical drive 1I: 1: 8 (port 1I: chassis 1: bay 8, 6TB SATA HDD, normal)
physical drive 1I: 1:10 (port 1I: chassis 1: bay 10, SATA 4 HDD, TB, OK)
physical drive 1I: 1:13 (port 1I: chassis 1: bay 13, 6TB SATA HDD, normal)
physical drive 2E: 1: 1 (port 2E: chassis 1: bay 1, 6TB SATA HDD, normal)
physical disk 2E: 1: 9 (port 2E: chassis 1: bay 9, SATA HDD, multiTB, normal)
physical disk 2E: 1: 9 (port 2E: chassis 1: bay, SATA HDD , 6 TB, normal)
Check bay G to see why it is marking the internal drive as external and try again.
- 2 minutes to read.
In This Article
DATA_BUS_ERROR error with value 0x0000002E. This usually indicates that a parity error has been detected in model memory.
DATA_BUS_ERROR Parameters
|
1 |
The virtual address that caused the error |
|
2 |
Physical reason causing the status error |
|
3 |
Processor Registration (PSR) |
|
4 |
Invalid Command Register (FIR) |
Reason
In most cases, this error is caused by a hardware problem — a specific configuration problem, faulty hardware, or incompatible hardware.
The most common hardware problems that can cause this error are bad RAM, L2 cache errors, or video memory errors. Damage to the hard drive can also cause this error.
This error checking can also be triggered when a device driver tries to access an address in the hob 0x8xxxxxxx that does not exist (in other words, that has no physical help to match).
Resolution
Hardware Troubleshooting: If hardware was recently added to the system, discard it to see if the error reoccurs.
If it was not possible to remove the existing hardware or update the faulty part. You should run the garden diagnostics provided by the manufacturer to determine which hardware component has failed. For details on these procedures, see the instruction manual for your computer. ConvinceEnsure that all adapter cards are correctly installed in the computer. Use an eraser or a good electrical contact cleaner available from health care stores to make sure the adapter card notifications are clean.
If the problem occurs on a specific recently installed system, check the uptime, which is most often associated with BIOS, SCSI controller, or network adapters updates. Updates in this category are usually available online or on the equipment manufacturer’s bulletin board system (BBS).
Otherwise, if the error occurs after the installation of a new or updated device owner is complete, the driver should be uninstalled. Under these circumstances, if a boot failure is required and the system partition is clearly NTFS formatted, you can use Safe Mode to rename or even remove the faulty driver.
If you are using the driver as part of your system investment in Safe Mode, you will need to restart your computer in Search Recovery Console to access it.ail.
In the Event Viewer system log, you can find additional error messages that can help identify a faulty device or driver. Disabling caching or memory shadow copying in the BIOS can also correct the nature of the error. Also check the root cause of the system with a modern commercial virus scanning software that will check the hard disk master boot record. Viruses can infect all Windows file devices.
To fix a damaged hard disk: run the chkdsk / f / r command available on the partition system. Before deploying a disk scan, you need to change the system. If you are unable to start the installation due to an error, use the recovery console and run chkdsk / r.
Warning If your program partition is formatted using the File Percentage Table (FAT) file system, long-running Windows filenames may become corrupted if Scandisk or another Microsoft MS-DOS hard disk drive tool is usedTo parse the file Sincerity. from the hard disk from MS-DOS. Always use the version of Chkdsk that works best for your version of Windows.
This theme is for web developers. If you are a customer who received a blue screen error code while using your computer, see Fixing Blue Screen Errors on Your Computer .
Improve the speed of your computer today by downloading this software - it will fix your PC problems.
Como No Mercado Corrigir Um Erro Fatal Do Sistema Com O Procedimento De Erro 0x0000002e 0x00000000
Cómo Corregir El Error Fatal Del Esquema Con El Código De Error 0x0000002e 0x00000000
Comment Corriger Une Erreur Système Fatale Avec Le Code Promotionnel D’erreur 0x0000002e 0x00000000
Hur åtgärdar Du Fatalt Strukturfel Med Felkoden 0x0000002e 0x00000000
Wie Sie Einen Schwerwiegenden Systemfehler Mit Dem Fehlerbereichscode 0x0000002e 0x00000000 Beheben Können
Hoe Een Fatale Systeemfout Op Te Lossen Met Foutstijl 0x0000002e 0x00000000
오류 접두사 0x0000002e 0x00000000으로 치명적인 시스템 오류를 수정하는 방법
Как исправить фатальную ошибку приложения с кодом ошибки 0x0000002e 0x00000000
Jak Naprawić Krytyczny Błąd Systemowy Z Hasłem Błędu 0x0000002e 0x00000000
Come Correggere L’errore Di Sistema Dannoso Con Il Codice Di Errore 0x0000002e 0x00000000
