Table of Contents
If you receive a “Backup Exec Bad Media” error code, read these troubleshooting tips.
PC running slow?
Microsoft no longer has this browser. Therefore, some of the features of this website may not be suitable for you. For the best experience on our website, consider upgrading to Microsoft Edge, Firefox, Chrome, or Safari.
You are using Microsoft Internet Explorer!
When I run backup management on disks 2 and 3, the tape is detected as bad media and the job fails,
PC running slow?
ASR Pro is the ultimate solution for your PC repair needs! Not only does it swiftly and safely diagnose and repair various Windows issues, but it also increases system performance, optimizes memory, improves security and fine tunes your PC for maximum reliability. So why wait? Get started today!
Intensive Execution Error: “A read / write error occurred in the spare memory. If the memory is an argument-based write, it is usually caused by contamination of the read / write heads on the tape drive. Clean the drive with tape. , and then try the specific task again. If the problem persists, try using a different tape. You can also check your cable, burner or other hardware.
Warning: disk warning or critical tape warning flag br> В В В В В В В В В В В В В В В В В В В В В В В В В В • • • • • • • “” “” “Warning: Warning drive or warning flag about 0x13 critical tape 19 < br> Ribbon warning indicator: 0x27, 39
This message was sent hands-free
IBM 3573-TL. generated
but when I start the service on disks 1 and 4, the job runs fine, no bad video is detected and I also have no emails from TL4000.
I am better off working for the company I work for and after that I have the job of replacing the sysadmin with the old “consultant” <--- air Quotes there. In your backup, Exec pushed the standard version, and it constantly appeared in the public domain. I changed the maximum backup disk size to 10 GB, which is the maximum number of backups per backup disk file to 200. Been more or less good for a month. Backups were ready 2 hours faster than previous failures. Everything is related to the sudden appearance of errors e00084c8. I looked through the competition logs and found that the current raid may have problems with the badblock. Which would be nice if I wasn't using Server Windows 2003 r2 for 2 terabytes of data. So, I found that I needed to run a good chkdsk that would shut down my DC for a few hours to fix the bad block. The problem is compounded by the fact that the software is largely “owned” by a previous consultant who chose not to keep it with a partner or to renew the support contract. I am using version 12.5 and want to poke a hole in Symantec Digi-Face, as I have done many times with Norton (thank goodness I removed the Norton tool). In the morning I try to take an evolutionary step, but it becomes such. I don't have a specific budget until next quarter. I'm looking for a backup of roughly 700GB over USB to help you with a "tape drive" (actually, it's a 2.5 "SATA that puts you in the trash ... it automatically shows up as solid state?) 750 gigabytes Tips are welcome ...
– fixed and no doubt he can even find a replacement job now twice as fast as before.
@matt – thanks forpresentation. I appreciate it. You don’t have to make me talk to everyone now.
[size = 18] [color = red] [b] List the version of Backup Exec along with the specific version you are actually using, which is very important for answering many questions [/ b] [/ color] [/ cut]
[b] Possible Cause: [/ b] Backup Exec cannot read or write data for reading or promotional or marketing materials. This issue is most likely caused by a hardware failure.
“Data error (likely cyclic redundancy check)” is displayed in Backup Exec. Run job log during unsuccessful backup / validation operation.
[url] http://support.veritas.com/docs/192216 [/ url]
You will try this too:
1 Under Devices, verify that Backup Console Exec is case-sensitive. Check to see if the show is labeled Bad Media.
2. Try to buy another tape.
3. If this tape also reports our own mistake, it means that it is not just a bad tape.
4. Then start the directory and try to make a backup.
It should work.
[b] Common causes of many CRC errors,as well as possible solutions to the problem: [/ b]
1. Dirty read / write heads on the device tape: contact your hardware manufacturer for proper cleaning methods.
2. Bad media:
■ Replacing the support.
· Try using a current tape that is certified for equipment from the current manufacturer.
3. Corrupted tape drivers have been shown to cause CRC errors.
Make sure you can download the latest tape drivers for your tape drives; VERITAS provides tape drivers as part of the VERITAS tape installer. You can download it if you want.
c: [url] http://www.symantec.com/business/support/downloads.jsp?pid=15047 [/ url]
4. The SCSI controller is poorly optimized to use wide consistency:
S Use each vendor’s SCSI configuration program to disable wide matching on the SCSI controller card.
■ If the device is a wide (68-pin) SCSI device, you should always use wide match. If device a is a filtered SCSI deviceChrome (50 pins), turn off Huge Negotiation.
6. SCSI controller high baud rate:
Use the manufacturer’s SCSI installer to reduce the SCSI transfer rate. (NOTE: Make sure the controller and backup device manufacturer has only the correct configuration for the SCSI upload speed.)
7.Synchronous SCSI controller negotiation enabled:
Use the manufacturer’s SCSI installer to synchronously disable arbitration on the SCSI controller card. Check controller and backup device
Manufacturers for the correct configuration for SCSI synchronous negotiation.
8. Incorrect termination or defective cables:
Make sure the SCSI cable is in good condition and configured for the correct SCSI connection. Don’t mix passive and active completion.
9. Verify that the entire tape drive is working properly:
Contact the tape drive manufacturer for diagnostic software that provides a test environment for the tape drive hardware.
10. Common SCSI Problems:
IsoSet the ribbon supply on a separate controller board.
Many CRC discrepancies are reported as Event 9 or 11 in Windows Event Viewer. See the following Microsoft article for troubleshooting event messages.
For more information, see Microsoft Article ID: Q154690
I hope this information will help you 🙂
Improve the speed of your computer today by downloading this software - it will fix your PC problems.Résoudre L’erreur Des Mauvais Annonceurs Dans Backup Exec
Backup Exec의 부적절한 미디어 오류 해결
Beheben Eines Falschen Medienfehlers In Backup Exec
Resolución Del Error De Soporte Drásticamente Incorrecto En Backup Exec
Löser Det Viktigaste Felmediafelet I Backup Exec
Naprawianie Błędu Nieprawidłowego Nośnika W Pobliżu Backup Exec
Resolvendo O Erro De Push Errado No Backup Exec
Risoluzione Dell’errore Materiale Errato In Backup Exec
Устранение ошибки неправильного носителя с помощью Backup Exec
De Fout Met Het Verkeerde Materiaal Oplossen In Backup Exec
